Home About Services RelaNex Academy Why Us Contact Get in Touch →
ENRUAZ

Protection & Automation Engineering

We assess, design and modify protection and control systems around the actual network configuration and operating requirements. Work may cover individual feeders and relays or coordinated schemes across a wider installation.

Relay Configuration & Protection Logic Development

Development and revision of relay configurations, including protection settings, programmable logic, I/O assignments, trip and alarm signals, interlocking and relevant communication interfaces, using the applicable manufacturer's engineering tools.

Relay configuration in detail →

Relay Settings Calculations & Coordination

Calculation and review of protection settings against equipment characteristics, fault conditions and operating scenarios, with coordination studies to assess selectivity and document any limitations.

Settings calculations in detail →

Protection Philosophy & Scheme Development

Definition of protection objectives, functions, operating principles and coordination requirements for new installations, existing networks and modernization projects.

Protection philosophy in detail →

Protection & Control Schematic Development

Development and revision of protection and control schematics, including CT/VT circuits, trip and close circuits, interlocks, alarms and interfaces with relays and control systems.

Schematic development in detail →

Protection System Modernization & Upgrades

Assessment and detailed engineering for aging protection systems, obsolete relays and revised protection requirements, including replacement selection, scheme adaptation and migration planning.

Modernization & upgrades in detail →

Protection & Control Reverse Engineering

Reconstruction of existing protection and control arrangements from available drawings, relay files and site information to support troubleshooting, documentation recovery and future modifications.

Reverse engineering in detail →

Protection Incident Analysis

Investigation of unwanted trips and failures to operate through analysis of disturbance records, event logs, relay settings and protection logic.

Incident analysis in detail →

Protection Change Assessment

Review of protection settings, logic and coordination following equipment additions, supply changes or modifications to network operating modes.

Change assessment in detail →

Independent Protection Engineering Consultancy

Technical assessments, design reviews, specification development and modernization advice to support informed decisions on protection and automation systems.

Engineering consultancy in detail →

ATS Circuit Design

We design Automatic Transfer Switch (ATS) schemes for critical and essential loads — implemented as hardwired logic, configured internally within numerical relays, or via dedicated PLC-based control — delivered using both traditional hardwired architecture and modern IEC 61850 digital standards.

ATS Circuit Design in detail →

IEC 61850 Engineering

Station bus design, SCL engineering and GOOSE schemes across multi-vendor systems.

IEC 61850 Engineering in detail →

Power System Studies

Power system studies establish the technical basis for equipment selection, protection settings and network modifications. We assess relevant operating scenarios for new installations and existing facilities, including proposed expansions and modernization.

Load Flow Analysis

Steady-state load flow studies that evaluate voltage profiles, power distribution, and loading conditions across the network — supporting planning, design validation, and operational optimization.

Load Flow Analysis in detail →

Short Circuit Analysis

Fault-current calculations across the network to assess equipment duties, support protection coordination and identify rating limitations under the studied operating conditions.

Short Circuit Analysis in detail →

Arc Flash Studies

Arc flash hazard analysis in accordance with international standards, determining incident energy levels and appropriate PPE categories to protect personnel working on or near electrical equipment.

Arc Flash Studies in detail →

Motor Starting Analysis

Analysis of motor startup behavior — voltage dip, starting current, and torque characteristics — to verify system stability and select appropriate starting methods for large motor loads.

Motor Starting Analysis in detail →

Power System Stability Analysis

Assessment of dynamic and transient stability, evaluating system behavior under disturbances, generator response and network resilience in the studied contingencies.

Power System Stability Analysis in detail →

Earthing System Design

Earthing and grounding system design against applicable project requirements and standards, assessing fault-current dissipation and relevant touch and step voltages to support personnel and equipment protection.

Earthing System Design in detail →

Power System Design

Network topology, substation configuration and equipment rating for HV and MV systems.

Power System Design in detail →

Electrical System Design

Plant-level electrical design, from load schedules and distribution to cable sizing, switchboard specification and installation drawings.

Electrical System Design in detail →

Maintenance Optimization & Asset Reliability

Unplanned downtime can have significant operational and financial consequences. We help prioritize maintenance according to equipment criticality, failure modes and operating requirements, using a structured, risk-based Reliability Centred Maintenance (RCM) approach.

RCM Strategy Development

Reliability Centred Maintenance strategy tailored for complex industrial environments, including Oil & Gas facilities — selecting an appropriate maintenance task for each asset, from predictive condition monitoring to strategic run-to-failure policies.

RCM Strategy Development in detail →

Criticality & FMECA Analysis

Failure Mode, Effects and Criticality Analysis that identifies asset failure modes, their effects, and operational consequences — so effort and budget are directed to your most critical assets.

Criticality & FMECA Analysis in detail →

Maintenance Program Optimization

Reviewing and refining your existing maintenance framework to cut waste and improve efficiency, directing budget and manpower toward the equipment that genuinely matters.

Maintenance Program Optimization in detail →

System-Wide Reliability Strategy

Reliability strategy recommendations across electrical power systems, protection equipment, and rotating machinery — a lean, optimized program built around how your assets actually fail.

System-Wide Reliability Strategy in detail →

A Fuller Technical Picture

Combined with our power system reliability studies, this gives a fuller picture of your facility: not only how reliable the system is today, but a prioritised roadmap for maintaining and improving it.

Power Automation & Control Systems

We develop power automation and control functions in coordination with the electrical network and protection philosophy. The scope can include transfer logic, interlocking, load shedding, PLC/SCADA interfaces and monitoring for new or existing installations.

ATS & Main-Tie-Main Control Schemes

Multi-source transfer logic beyond the scope of fixed-function transfer controllers.

ATS & Main-Tie-Main Control Schemes in detail →

Substation SCADA & ECMS

A monitoring layer over your MV and LV network that operators can actually act on.

Substation SCADA & ECMS in detail →

Power Management & Fast Load Shedding

Fast, selective load shedding designed around the studied contingencies of islanded and captive networks.

Power Management & Fast Load Shedding in detail →

Legacy PLC Migration & Retrofit

Moving obsolete switchboard controllers to current platforms, with the existing logic recovered and documented first.

Legacy PLC Migration & Retrofit in detail →

Substation Automation

The control, monitoring and interlocking layer that makes a substation operable.

Substation Automation in detail →

How an automation package is executed

Automation packages typically follow four stages, so the customer can see what exists at each stage and the logic is checked against the agreed scenarios before hardware is assembled.

1

Electrical design and I/O mapping

Control schematics translated into an automated system: control transformer sizing, interlock coils, sensor supplies, and the master PLC I/O assignment schedule.

2

Logic and interface development

PLC algorithms, safety interlocks, communication driver mapping and HMI or SCADA runtime graphics, built from the agreed control philosophy and cause-and-effect matrix.

3

Virtual factory acceptance test

Logic verified in simulation with S7-PLCSIM Advanced and WinCC Runtime against the defined operating and failure scenarios before hardware is assembled, with a recorded demonstration of those scenarios and a live vFAT session over screen share. Simulation does not replace the hardware and site tests that follow.

4

Commissioning support

Code loaded to the physical hardware and checked through panel and site testing, supported in the customer's workshop, on site or remotely. Any remote connection to site systems is agreed separately and follows the customer's access and cybersecurity procedures.

Vendor-Independent Expertise

RelaNex Group is vendor-independent: our recommendations and engineering are not restricted to one manufacturer. We develop settings, logic and configuration deliverables using the applicable manufacturer's engineering environment, with the supported relay model, firmware and required functions confirmed during scoping. ATS schemes can be configured internally within the relays or via dedicated PLCs, in either hardwired or IEC 61850 architecture.

ABBHitachi EnergySiemensSchneider ElectricGE VernovaSEL

Consulting, Detailed Engineering — or Both

Consulting & Technical Assessment

Independent reviews, incident investigations, modernization strategies, technical specifications and recommendations that help define what needs to change and why.

Detailed Engineering

Calculations, settings schedules, relay configuration files, logic diagrams, schematics and technical documentation needed to develop the agreed solution.

The final deliverables and any implementation support are defined in the project scope.

Remote Engineering & Technical Support

Access specialist protection and power system expertise without requiring an engineer to be present for every stage of the work. We deliver remote assessments, calculations, design development and technical reviews using the agreed project information and communication arrangements.

  • Protection settings calculations and coordination studies
  • Relay configuration and programmable logic development
  • Review of existing settings, configurations and schematics
  • Disturbance-record and event-log analysis
  • Protection and control schematic development
  • Modernization assessments and reverse-engineering support
  • Technical document and vendor-submission reviews
  • Engineering clarification during site testing and implementation

Remote support is coordinated with the personnel responsible for the installation. Activities requiring physical verification, equipment operation or testing remain subject to the agreed site responsibilities and procedures.

Tell Us What Your System Needs

Share your project objective or describe the protection issue you are experiencing. We will identify the information needed to scope the work.

Get in Touch